{"id":11376,"date":"2021-09-18T09:54:45","date_gmt":"2021-09-18T08:54:45","guid":{"rendered":"https:\/\/www.prophotonix.com\/?p=11376"},"modified":"2021-10-06T10:56:08","modified_gmt":"2021-10-06T09:56:08","slug":"led-vs-halogen-technology-for-hyperspectral-imaging","status":"publish","type":"post","link":"https:\/\/www.prophotonix.com\/led-vs-halogen-technology-for-hyperspectral-imaging\/","title":{"rendered":"LED vs Halogen Technology for Hyperspectral Imaging"},"content":{"rendered":"

Hyperspectral imaging, a rapidly advancing technology, is a method used to obtain spectral data of a target using a large number of detection bands, generally greater than ten. This post will discuss the specification considerations when selecting either LED or Halogen illumination in hyperspectral imaging applications, which include spectral matching, uniformity, lifetime, form factor, energy efficiency, environmental issues and strobe control.<\/p>\n

Spectral Matching<\/h2>\n

The broad nature of the spectrum of Halogen lamps, see Figure 1, has made them the traditional choice for hyperspectral applications. Recent technology advancements, however, have made broadband illumination a possibility using LEDs. An advantage of using hyperspectral LED lights<\/a>, as opposed to Halogen, is the capability to boost the spectrum as required within the range of interest. This is beneficial for applications where illumination is needed to make up for any deficiencies caused by a camera\u2019s response sensitivity or when matching a specific spectral profile is a requirement for the light source.<\/p>\n

\"\"<\/p>\n

Figure 1: A typical Halogen light source spectrum showing the heavy bias toward infrared<\/span><\/p>\n

Spectral boosting using LEDs can lead to a more even response and thus an improved signal-to-noise ratio, as shown in Figure 2. This figure displays the use of a LED illuminator over a wide spectral range where large variations in camera sensitivity can occur. The spectrum in Figure 2 was created by ProPhotonix and demonstrates the capability to boost the UV and IR regions according to customer specifications.<\/p>\n

\"\"<\/p>\n

Figure 2: LED spectrum weighted toward ultraviolet and infrared in order to counteract camera sensitivity curves and improve signal-to-noise ratio<\/span><\/p>\n

Uniformity-Blue Spectral Weakness<\/h2>\n

Uniformity is extremely important in hyperspectral imaging. Halogen lamps have a continuous spectrum in the range from 300nm to 2500nm .However, this emission varies considerably across the range, the emission below 500nm is very weak while \u00a0the emission in long IR is very strong but this is often undesirable as it can cause unwanted heat emission. It is not possible to adjust this spectrum without the use of costly filters. etc.<\/p>\n

ProPhotonix manufactures the COBRA MultiSpec<\/a> withChip-on-Board LED Technology and our in-house design and engineering capability ensures we can accommodate custom requests.<\/p>\n

Lifetime<\/h2>\n

The lifetime of the light source can be an important consideration for many hyperspectral applications, especially in production environments where maintenance or replacement of an illuminator can mean significant throughput loss in downtime. Halogen lamps have an average lifetime of several thousand hours. LEDs, in comparison, have a lifetime of tens of thousands of hours. This is at least an order of magnitude better than the lifetime of a Halogen lamp.<\/p>\n

In addition, with the inherent flexibility of Chip-on-Board LED<\/a>-based products like the Cobra MultiSpec, ProPhotonix can design the LED array to reduce the thermal stress on any LEDs that may be less efficient in terms of optical output. The ratio of LEDs incorporated for each wavelength is adjusted to take account of efficiency, thereby leading to improved performance and extended lifetimes.<\/p>\n

Form Factor<\/h2>\n

Halogen lights generate excess heat. This can create additional challenges as this heat can damage the material undergoing inspection. LEDs generate low levels of heat in the emission direction thus significantly reducing on-target heating. The COBRA MultiSpec<\/a> is a modular light composed of 100mm units,up to a total length of 5m,and has twelve individually controlled channels. Customizing the wavelength selection means that the COBRA MultiSpec can be configured for both hyperspectral and multispectral applications.<\/p>\n

\n